Guide

SMB and prosumer network optics: Ubiquiti, MikroTik, Netgear and the rest decoded

There is a reversal in this part of the market that nobody warns you about. The enterprise vendors give you opaque order codes and forgiving hardware. The small-business and prosumer vendors do the opposite:…

21 min read Published 17 novembre 2026
Gigabit network switch with Ethernet cables connected

There is a reversal in this part of the market that nobody warns you about. The enterprise vendors give you opaque order codes and forgiving hardware. The small-business and prosumer vendors do the opposite: their part numbers are the most readable in the industry — a MikroTik S+31DLC10D tells you the form factor, the wavelength, the connector, the reach and the diagnostics in nine characters — and then the switch in front of you is the one most likely to refuse a module it does not recognise.

That is the shape of the problem this guide solves. It covers how the Ubiquiti, MikroTik, Netgear, TP-Link, D-Link, Zyxel, Allied Telesis and PLANET part numbers read, the three things that reliably go wrong in this segment, and the 124 SMB network optics Carritech holds, listed by speed from 155 Mbit/s to 100 Gigabit.

One number sets this range apart from every other on this site: 17 of the 124 parts are copper. That is roughly one in seven, where a switching vendor’s optics range runs closer to one in twenty-five. It is the clearest single fact about this market. The networks these modules go into are copper networks with fibre at the edges, so an RJ45 in an SFP cage is not a curiosity here — it is a mainstream product. The second number worth knowing: 12 of the 25 records in our entire 10G CWDM range are Ubiquiti. A brand most people associate with wireless access points is half of our coloured 10 Gigabit catalogue.

The eight naming schemes, best to worst

Two of these are a pleasure to work with, four are serviceable, and two will make you open a data sheet. Ranked by how much the string tells you:

VendorExampleHow it reads
MikroTikXS+31LC10DThe best scheme in the industry. Rate prefix, wavelength, connector, reach, diagnostics. Decoded below.
NetgearAXM762Three-letter prefix encodes the speed generation: AFM, AGM, AXM, AXLM, ACM. Decoded below.
ZyxelSFP25G-LRCurrent parts are descriptive. Older ones (SFP-SX-D, SFP-LX-10-D) use a different, also readable, convention.
TP-LinkTL-SM5110-LRTwo families. TL-SM3nn is the older gigabit line; SM5110/SM6110/SM9110 are 10G, 25G and 100G.
Allied TelesisAT-SP10LRAT-SP then a loose description. The reach digits are reliable; the letters are not — see below.
UbiquitiUACC-OM-SM-10G-DUACC-OM- for optical modules, UACC-CM- for copper, UF- for the older UFiber parts. Media and rate, no reach.
D-LinkDEM-432XTDEM- plus a number whose leading digits track the speed. Decoded below, with one caution.
PLANETMFB-FA20MFB-F then a half letter and the reach. Compact but you need to know the convention.

MikroTik, decoded character by character

This is worth learning because it is genuinely complete. Taking the 10 Gigabit single-mode part as the worked example:

  • First group — the rate and cage. S- is a gigabit SFP, S+ an SFP+ at 10G, XS+ an SFP28 at 25G, Q+ a QSFP+ at 40G and XQ+ a QSFP28 at 100G. So S-85DLC05D, S+85DLC03D, XS+85LC01D, Q+85MP01D et XQ+85MP01D are the same 850 nm multimode idea at five speeds.
  • Next two digits — the wavelength. 85 is 850 nm, 31 is 1310 nm, 55 is 1550 nm.
  • Then the connector. DLC is duplex LC, LC is LC, MP is an MPO trunk. That one field tells you whether you need a patch lead or a twelve-fibre trunk, which no other vendor in this table puts in the part number at all.
  • Then the reach, in hundreds of metres or kilometres. 01 is 100 m, 03 is 300 m, 05 is 500 m, 02 is 2 km, 10 is 10 km, 20 is 20 km, 80 is 80 km. Hence XQ+31LC02D is the 2 km CWDM4 part and XQ+31LC10D the 10 km LR4.
  • Trailing D — digital diagnostics. Present on all of them.

Netgear’s scheme is cruder and almost as useful, because the three-letter prefix is a generation marker. AFM is Fast Ethernet — AFM735 is a genuine 100BASE-FX part. AGM is gigabit (AGM731F, AGM732F, AGM733, AGM734). AXM is 10 Gigabit, AXLM is 40 and ACM is 100 — AXLM762, ACM761, ACM762. Read the prefix and you know the speed before you know anything else.

D-Link’s DEM- numbers track speed in the leading digits — DEM-2nn at 100 Mbit/s, DEM-3nn at gigabit, DEM-4nn at 10 Gigabit, DEM-QX at 40 and DEM-S2 at 25 — with one exception that matters. DEM-311GT et DEM-312GT2 are gigabit parts in the 3xx band as you would expect, but DEM-310GT et DEM-315GT are single-mode and DEM-311GT is multimode, so the last digit is not a reach ladder. Check the part, not the neighbourhood.

The Ubiquiti CWDM plan, the two holes in it, and one you need to ask us about

This is the most interesting thing in the range and it has a commercial edge, so it gets its own section.

Ubiquiti ships a twelve-channel 10 Gigabit CWDM set: UACC-OM-SFP10-1270, UACC-OM-SFP10-1290, UACC-OM-SFP10-1310, UACC-OM-SFP10-1330, UACC-OM-SFP10-1450, UACC-OM-SFP10-1470, UACC-OM-SFP10-1490, UACC-OM-SFP10-1510, UACC-OM-SFP10-1530, UACC-OM-SFP10-1550, UACC-OM-SFP10-1570, UACC-OM-SFP10-1590. The ITU-T G.694.2 CWDM grid, whose in-force edition dates from December 2003, runs on 20 nm spacing from 1271 to 1611 nm — eighteen channels. Ubiquiti supplies twelve of them, and the six it leaves out are not a random subset.

  • Five of the six missing channels are consecutive and sit between 1330 and 1450 nm. That is the water peak: the hydroxyl absorption band centred near 1383 nm, where ordinary single-mode fibre attenuates far more than it does either side of it. Low-water-peak fibre to the later editions of ITU-T G.652 — in-force edition August 2024 — largely removes the problem, but a great deal of installed fibre is older than that, and a vendor selling into buildings with unknown fibre is sensible to skip those channels entirely. It is a deliberate, well-judged omission and it tells you something about who the range is for.
  • The sixth missing channel is 1611 nm, the top of the grid, which is simply where the range stops.

Now the part we would rather you heard from us than worked out from a product page. All twelve of those Ubiquiti channels currently map to a single Carritech record, CT-SFP+CWXX-40, whose stated wavelength range is 1470–1610 nm. Seven of the twelve sit inside that range. Five — 1270, 1290, 1310, 1330 and 1450 — sit outside it, and the O-band channels in particular are a different optical design from a C-band or L-band CWDM part: different laser, different fibre attenuation, different budget. We are splitting the record. In the meantime, if you need an O-band CWDM channel, say the channel number when you order and we will confirm the wavelength in writing before anything ships. On a coloured system the wavelength is the whole product; getting it approximately right is getting it wrong. Our coloured 10 Gigabit range and the guide to 10G DWDM and CWDM SFP+ cover the grid choice, and CWDM vs DWDM covers which one your system wants.

Copper in an SMB network is a whole physical layer, and two records need a conversation

A copper SFP contains no laser. It is a complete 1000BASE-T or IEEE Std 802.3an-2006 10GBASE-T physical layer squeezed into a cage designed for an optical module, and it behaves accordingly: it draws more power, it runs hotter, it adds latency the optical parts do not, and at 10 Gigabit it reaches about 30 metres on Category 6A rather than the 100 metres a native RJ45 port gives you. The multi-rate behaviour — 2.5GBASE-T and 5GBASE-T — comes from IEEE Std 802.3bz-2016, approved on 22 September 2016, but whether a given switch will bring the port up at 2.5G is a software question rather than a property of the module.

On a small switch with eight ports and a modest power budget, that is a design constraint rather than a footnote. Two of these modules in the uplink cages of a compact switch can be a measurable share of its thermal headroom.

And there is a record we need to be straight about. Four parts in the copper list below — S+RJ10, UACC-CM-RJ45-MG, AXM765 et AXM765v2 — are 10 Gigabit multi-gigabit copper modules currently mapped to a Carritech record whose product title describes a gigabit part. The title is what is wrong; the requirement these parts are listed against is 10 Gigabit. The 30-metre designs — UACC-CM-RJ45-10G, AT-SP10T, DEM-410T, SFP10G-T, TL-SM5310-T — are specified correctly. We are fixing the 80-metre record, and this is the third time it has been flagged, so it is overdue. Until it is corrected, do not take the rate at 80 metres from this website — ask us and we will confirm it against the module’s own specification. Copper SFP and 10GBASE-T SFP+ modules covers the power, heat and auto-negotiation detail, and copper SFPs and adapters is the range.

Three more things that catch people out

1. 🔴 One D-Link BiDi pair currently points at the same half twice

This is the finding in this article most likely to cost you an evening, and it is ours, not D-Link’s.

DEM-436XT-BXD et DEM-436XT-BXU are the downstream and upstream halves of a 10 Gigabit single-fibre pair. Both currently map to the same Carritech upstream design. Order one of each from those two pages and you can end up with two upstream modules, which will never link — both ends transmit on the same wavelength and listen on the other, and the diagnostics show a healthy transmitter and no received power at both ends, which looks exactly like a broken fibre.

We are correcting the mapping. In the meantime, order 10 Gigabit BiDi pairs by telling us the route and the two platforms rather than by picking two part numbers from the catalogue, and we will send a matched pair. The gigabit pair in the same range is mapped correctly — DEM-331R is the upstream half and DEM-331T the downstream — as are the 155M pairs. BiDi transceivers explains the pairing rule and BiDi SFP modules is the complete single-fibre range.

2. The 155M category holds gigabit modules, and six of them are in this range

Our 155M Duplex SFP category contains a number of 1000BASE-SX gigabit modules that are filed at the wrong speed on our side. In this range that affects AGM731F, AT-SPSX, AT-SPSX/I, AT-SPSX-90, SFP-SX-D, SFP-SX-E, ISM311LM, TL-SM311LM, S-85DLC05D, DEM-311GT, DEM-312GT2 and the Ubiquiti gigabit multimode parts. They are gigabit parts and they behave like gigabit parts — the classification is wrong, not the module. If you need a genuine Fast Ethernet optic for an old link, ask for 100FX explicitly: AFM735, DEM-210 et DEM-211 are the real 100BASE-FX parts here. See 155M and 1.25G SFP modules.

3. Suffixes mark variants our records do not currently separate

Three vendors in this range use a trailing marker for a variant of the same optical design, and in each case our product records map the variant and the base part to the same profile with the same description:

Optically these pairs really are the same module. The rating is the thing that differs, and it is the thing you are buying if the switch is in a plant room, a riser cupboard, a roadside cabinet or a ceiling void — which in this segment it very often is. Our records do not currently tell the pairs apart, so tell us the ambient and we will confirm the temperature rating in writing before anything ships. It is a much cheaper conversation than a module that drifts out of specification every August.

Two more small things in the same spirit, offered plainly. Allied Telesis’s letters and the industry’s do not agree: AT-SPLX40 is the 40 kilometre part and AT-SPEX is not, despite the EX, so read the reach digits and ignore the letters in this family. And the gigabit single-mode record several of these parts map to carries a title saying 10 km and a body saying 20 km, which matters because MikroTik’s S-31DLC20D says 20 in its own part number. Where the span is anywhere near either figure, get it from us rather than from the page — and work the numbers with why optical link budget matters rather than trusting a round number.

Which cage takes which speed

CageSpeeds it will takeWhere you find it in this segment
SFP100M, 1GUplinks on access switches, fibre downlinks, point-to-point building links
SFP+1G, 10GThe workhorse. Uplinks on almost every current SMB switch
SFP2810G, 25GAggregation on the newest kit. Will usually run at 10G — confirm with the vendor
QSFP+40G, or 4 × 10G broken outStacking and aggregation on larger switches
QSFP28100G, or 4 × 25G broken outTop of the range. Often the only 100G ports in the building

Two notes for the order rather than the reading. An SFP28 cage will usually run at 10G and sometimes at 1G, but which lower rates are offered is a platform and software question rather than a property of the module — SFP+ vs SFP28 covers it, and in this segment the answer is less often yes than it is on enterprise hardware. And a 40G or 100G port that breaks out to four lower-speed links is the cheapest capacity available on hardware you already own, provided the switch supports the split — breakout explained covers the mechanics.

What the switch checks, and what it does not

What a switch reads when a module seats is the identification data in the module’s EEPROM, laid out to the SFF management specifications held in the SNIA SFF specifications library, and compares it against what its firmware expects for that port. If the strings line up, the port comes up and the optic appears in the inventory like any other. If they do not, behaviour ranges from a log entry to a port that stays down.

This is the segment where that check bites hardest, and it is worth being clear about why. On enterprise hardware an unrecognised module is usually a warning and a working link. On consumer and small-business switches the firmware is simpler, the support list is shorter, and there is frequently no command to override it. The module has to present the string the switch is looking for, which is what transceiver coding is, and what the Carritech Opticode coding box does at the point of deployment rather than at the point of order.

What the switch does not do is measure the optic. It cannot tell you whether the launch power is in specification, whether the receiver sensitivity matches the data sheet, or whether the part will still be in specification in three years. That is why every Carritech module is measured against its specification before despatch — see the 22 checks a module passes. On a small network with no spare ports and no second path, a module that was measured before it shipped is worth more than one that was not, because there is nowhere to move the link to while you find out. Spotting a failing fibre link before it drops covers reading the diagnostics once it is in, and fibre optic connector cleaning is the cheapest decibel you will ever recover.

On the procurement questions, compatible optical transceivers vs OEM, OEM vs compatible: cost, risk and performance compared et do third-party optical transceivers void your warranty? answer them straight — and in this segment the price gap between an OEM-branded module and a tested compatible one is frequently a larger share of the project than the switch is.

Five checks before you order

  • Quote the switch model and the firmware release, not just the optic. In this segment the support list is short and the override frequently does not exist.
  • On a coloured link, quote the channel. A CWDM wavelength is the product, and the O-band channels are a different design from the C-band ones.
  • Say where the switch lives. If it is anywhere other than a comms room, the temperature rating needs confirming rather than assuming.
  • For copper, confirm the rate and the reach together, and confirm the switch will power the module — a 10GBASE-T module is a far heavier electrical load than an optical one.
  • For single-fibre links, order a matched pair from us rather than picking two part numbers, and record which wavelength plan the route uses somewhere other than one person’s memory.

The SMB and prosumer network optics Carritech stocks

One hundred and twenty-four tested part numbers across eight vendors, every one coded for the platform it is going into and measured against its specification before despatch. Listed by speed and form factor below.

155M and gigabit SFP — 39 parts

Filed at 155M, 17 parts. AFM735, AGM731F, AT-SPSX, AT-SPSX-90, AT-SPSX/I, DEM-210, DEM-211, DEM-311GT, DEM-312GT2, ISM311LM, S-85DLC05D, SFP-SX-D, SFP-SX-E, TL-SM311LM, UACC-OM-MM-1G-D, UACC-OM-MM-1G-D-2, UF-MM-1G. As set out above, only AFM735, DEM-210 et DEM-211 are genuine Fast Ethernet optics — 100BASE-FX at 1310 nm over 2 km. The rest are 1000BASE-SX gigabit modules mis-filed on our side. Note that UACC-OM-MM-1G-D et UACC-OM-MM-1G-D (duplicate record) are the same Ubiquiti part held twice in our catalogue; we are merging them. Browse the 155M duplex SFP range and the 155M transceivers page.

1.25G duplex SFP, 16 parts. AGM732F, AGM733, AT-SPEX, AT-SPLX10, AT-SPLX10/I, AT-SPLX40, AT-SPZX120/I, AT-SPZX80, DEM-310GT, DEM-315GT, ISM311LS, S-31DLC20D, S-55DLC80D, SFP-LX-10-D, SFP-LX-10-E, TL-SM311LS. The reach ladder in this group runs from LX at 10 km through EX at 40 to ZX at 80 and EZX at 120, which is further than most people expect from a segment associated with office switches — and it is exactly right, because the networks that buy gigabit single-mode optics in volume are municipal, campus, utility and wireless-backhaul networks rather than offices. Browse the 1.25G duplex SFP range and the 1.25G transceivers page.

155M BiDi, 4 parts. MFB-FA20, MFB-FB20, SFP-100BX1310-20-D, SFP-100BX1550-20-D — two matched single-fibre pairs at 1310/1550 nm over 20 km. 1.25G BiDi, 2 parts. DEM-331R, DEM-331T — a matched gigabit pair at 40 km. Single-strand working at 100 Mbit/s and 1 Gbit/s is the one part of the BiDi family that IEEE 802.3 actually standardises, as 100BASE-BX and 1000BASE-BX, which makes these the most interoperable BiDi parts you can buy. They are still sold in halves and two of the same half will never link. See BiDi SFP modules and browse the 155M BiDi et 1.25G BiDi ranges.

1.25G CSFP, 1 part. AT-SPBD20DUAL-13 is the most unusual module in this range and the most useful if it fits your problem: a compact SFP carrying two independent single-fibre gigabit links in one cage, upstream at 1310 nm and downstream at 1490, over 20 km. It doubles a cabinet’s port count without new hardware and without new fibre. It is the upstream member of a pair and must be matched with the corresponding downstream part. See 1.25G CSFP optical transceivers and browse the 1,25G CSFP range.

Copper SFP and SFP+ — 17 parts, one in seven of the range

AGM734, AT-SP10T, AT-SPTX, AT-SPTX-90, AT-SPTX/I, AXM765, AXM765v2, DEM-410T, S+RJ10, S-RJ01, SFP-1000T, SFP10G-T, TL-SM331T, TL-SM5310-T, UACC-CM-RJ45-10G, UACC-CM-RJ45-1G, UACC-CM-RJ45-MG. The gigabit 1000BASE-T designs are AGM734, AT-SPTX, AT-SPTX-90, AT-SPTX/I, S-RJ01, SFP-1000T, TL-SM331T et UACC-CM-RJ45-1G; the 30-metre 10 Gigabit designs are AT-SP10T, DEM-410T, SFP10G-T, TL-SM5310-T et UACC-CM-RJ45-10G; and AXM765, AXM765v2, S+RJ10 et UACC-CM-RJ45-MG are the longer-reach multi-gigabit parts we would rather you asked us about than read off the page. See copper SFP modules and browse copper SFP and SFP+.

10G SFP+ — 40 parts, the largest block

10G duplex SFP+, 26 parts. AT-SP10ER40/I, AT-SP10LR, AT-SP10LR/I, AT-SP10SR, AT-SP10SR/I, AT-SP10ZR80/I, AXM761, AXM762, AXM764, DEM-431XT, DEM-431XT-DD, DEM-431XT-SR, DEM-432XT, DEM-432XT-DD, DEM-433XT, S+31DLC10D, S+85DLC03D, SFP10G-LR, SFP10G-LR-E, SFP10G-SR, SFP10G-SR-E, TL-SM5110-LR, TL-SM5110-SR, UACC-OM-MM-10G-D, UACC-OM-SM-10G-D, UF-MM-10G. The full reach ladder: SR on multimode, LR at 10 km, ER at 40 and ZR at 80. The port types come from IEEE Std 802.3ae-2002, approved at the June 2002 Standards Board meeting, and there is no forward error correction at 10G over fibre, which means an error counter on a 10G port means exactly what it appears to mean — a genuinely useful property on hardware whose diagnostics are otherwise thin. One note on the long parts: the Carritech design that AT-SP10ZR80/I maps to is a single-wavelength grey 1550 nm module, and its description currently calls it DWDM. It is a grey part; if you are planning a coloured system, say so and we will quote coloured optics. See SFP-10G-SR: the full specification and browse the 10G duplex SFP+ range.

10G CWDM SFP+, 12 parts. UACC-OM-SFP10-1270, UACC-OM-SFP10-1290, UACC-OM-SFP10-1310, UACC-OM-SFP10-1330, UACC-OM-SFP10-1450, UACC-OM-SFP10-1470, UACC-OM-SFP10-1490, UACC-OM-SFP10-1510, UACC-OM-SFP10-1530, UACC-OM-SFP10-1550, UACC-OM-SFP10-1570, UACC-OM-SFP10-1590 — the twelve-channel Ubiquiti plan discussed above. Read that section before ordering an O-band channel. Browse the 10G CWDM SFP+ range.

10G BiDi SFP+, 2 parts. DEM-436XT-BXD, DEM-436XT-BXU — the pair whose mapping we are correcting, as described above. Browse the 10G BiDi SFP+ range, and the 10G transceivers page for the rest of the ten-gigabit catalogue.

25G SFP28 — 8 parts

DEM-S2801SR, DEM-S2810LR, SFP25G-LR, SFP25G-SR, SM6110-LR, SM6110-SR, XS+31LC10D, XS+85LC01D — SR on multimode and LR at 10 km. 25 Gigabit Ethernet comes from IEEE Std 802.3by-2016, approved on 30 June 2016. FEC configuration is the usual reason a 25G link stays down, it is a host setting rather than a module property, and both ends have to agree — which on small-business hardware means finding out whether the switch exposes the setting at all. Settle it before the install window. See 25G SFP28 transceivers et forward error correction explained, and browse the 25G SFP28 range.

40G QSFP+ and 100G QSFP28 — 19 parts

40G QSFP+, 7 parts. AT-QSFPER4, AT-QSFPLR4, AT-QSFPSR4, AXLM762, DEM-QX01Q-SR4, DEM-QX10Q-LR4, Q+85MP01D — SR4 on an eight-fibre MPO trunk, LR4 at 10 km and ER4 at 40 on single-mode. 40 Gigabit Ethernet arrived with IEEE Std 802.3ba-2010, approved in June 2010. The multimode parts need an MPO rather than a duplex LC, so MPO polarity is worth checking before the install rather than during it. See 40G QSFP+ transceivers and browse the 40G QSFP+ range.

100G QSFP28, 12 parts. ACM761, ACM762, AT-QSFP28-LR4, AT-QSFP28-SR4, QSFP100G-LR4, QSFP100G-SR4, SM9110-SR4, UACC-OM-QSFP28-LR4, UACC-OM-QSFP28-SR4, XQ+31LC02D, XQ+31LC10D, XQ+85MP01D — SR4 on multimode from IEEE Std 802.3bm-2015, approved on 16 February 2015; CWDM4 at 2 km (XQ+31LC02D); and LR4 at 10 km. At 100G and above forward error correction is part of the interface and permanently on, so a healthy port shows a steadily climbing corrected-codeword count rather than zero — which catches people out the first time they look at one. The 2 km decision is set out in 100G QSFP28 transceivers and the longer options in 100G ZR4 vs LR4 vs ER4. Browse the 100G QSFP28 range and the 100G transceivers et 40G transceivers pages.

Inside the rack, do not buy optics at all

This is the easiest saving on the list above and it is bigger here than in an enterprise estate, because the links are shorter. For a run from a server or a NAS to the switch above it, two transceivers and a patch lead cost more than a cable, draw power at both ends, add two connectors to keep clean and two optical budgets to manage. The 10G SFP+ et 25G SFP28 direct attach ranges cover exactly that case, with active optical cable where the run is longer or the copper too stiff for the cable management in a small cabinet. See DAC and AOC cables et DAC vs AOC.

One point specific to this segment: a cable assembly has an EEPROM at each end, and each end faces a different device. A Ubiquiti switch at one end and a MikroTik or a Netgear at the other means the assembly needs correct identification twice, to two different firmware families’ expectations — and mixed-vendor is the norm here rather than the exception, because these networks are assembled rather than specified. Plenty of suppliers can code one end. Coding both is what the Opticode coding box does, and it is the difference between a cable that works and a cable that comes up on one side only.

Getting SMB network optics without the OEM price

Carritech Optics holds the Ubiquiti, MikroTik, Netgear, TP-Link, D-Link, Zyxel, Allied Telesis and PLANET coded range in UK and EU stock, from 155M et 1.25G through 10G, 25G et 40G to 100G, with copper SFPs and adapters, patch cords et media converters alongside for the jobs a pluggable cannot do.

Every module is coded for the target platform and measured against its specification before despatch, and carries a garantie à vie with UK and EU stock and support behind it. The stock argument lands differently here than it does in a data centre: the problem in this segment is not volume, it is variety. An integrator or a managed service provider carries three brands of switch across forty sites, and holding one line item per vendor string means holding four times the stock to cover the same four optical designs. Holding one optical design per reach and coding at the point of deployment is the answer, and it is set out in building a smarter transceiver stock strategy. Your optics will go end-of-sale before your switch does is worth reading before you standardise, and it bites hard in this segment because the switches outlive their vendors’ interest in them. Our accreditations, why choose us et support pages cover how we work, and the knowledge centre holds the rest of the technical library. Our guides to Arista, Nokia, HPE and Aruba, Dell, Brocade et NVIDIA compatible optics cover the enterprise vendors you will meet at the other end of an uplink.

Trying to work out which CWDM channel a Ubiquiti part number means, whether a switch will bring an SFP28 port up at 10G, or what a MikroTik string actually specifies? Tell us the switch model, the firmware release and what is at the far end and we will say. Our compatibility checker returns the tested Carritech equivalent of an OEM part number in seconds, upload a whole part-number list and we will price it, or request a quote.

Demander des échantillons de produits

Saisissez vos coordonnées ci-dessous pour demander des échantillons de nos émetteurs-récepteurs optiques.

Demande de prix